Transparent Sony WM-EX672

Discussion in 'Gallery' started by Emiel, Oct 2, 2023.

  1. Emiel

    Emiel Well-Known Member S2G Supporter

    Messages:
    1,001
    Trophy Points:
    113
    Location:
    Western Europe
    A while back I bought a Sony WM-EX672 that needed a new belt.
    While looking for the service manual, I found a seller on AliExpress that offered a complete housing including battery door for it, entirely transparent.
    After the housing and new belt from @mihokm were installed, I was simply amazed. It is mesmerizing to watch, the back more so than the front!
    GIF-2023-09-20-14-17-04.gif GIF-2023-09-20-14-18-38.gif IMG_2919.jpeg
     
  2. Mister X

    Mister X Moderator Staff Member

    Messages:
    15,605
    Trophy Points:
    113
    Location:
    Minnesota
    That looks great, is it a real injection molded part?
     
  3. On The Beach

    On The Beach Active Member

    Messages:
    234
    Trophy Points:
    43
    Location:
    Australia
    I’ve seen these a while ago on Aliexpress. Not real cheap (I would have thought around $10 but I saw about $60 for only a door) and I wondered if the fit well.

    do you recommend? Are they made well?
     
    Last edited: Oct 3, 2023
  4. Emiel

    Emiel Well-Known Member S2G Supporter

    Messages:
    1,001
    Trophy Points:
    113
    Location:
    Western Europe
    This one was 35 euros approximately delivered, so I decided to buy it.
    Occasionally, only the cassette door for 50+ appears in my list; I find that a bit too expensive.
    The fit is good, down to the plastic tabs that touch the domes of the buttons on the back.
    The only change I need to make is the cut outs for the battery sidecar, they are a hair too small.
    It should be easy to enlarge carefully with a drill.

    It seems so, I can't imagine it being 3D printed.
     
    Mister X and On The Beach like this.
  5. Mister X

    Mister X Moderator Staff Member

    Messages:
    15,605
    Trophy Points:
    113
    Location:
    Minnesota
    I'm not a user of 3D but I think you can see the lines of the rod with 3D. With injection you might have some flashing (smushed plastic that squeezed through the mold), or even round ejection pin marks.

    Injection would be impressive since they would have to mill a metal mold. They might also be resin casting, I'm not sure how you can tell the difference.
     
  6. Emiel

    Emiel Well-Known Member S2G Supporter

    Messages:
    1,001
    Trophy Points:
    113
    Location:
    Western Europe
    There are no pin marks, the surface is completely smooth (exterior and interior).
     
  7. Rune Lindman

    Rune Lindman Member

    Messages:
    92
    Trophy Points:
    18
    Location:
    Sweden
    Funny, I remember back in the day it was cool not to show the cassette to make it more modern, now I really enjoy watching the cassette spin whilelistening.
     
    On The Beach likes this.
  8. Derek marshall

    Derek marshall Well-Known Member

    Messages:
    630
    Trophy Points:
    63
    Location:
    Kent
    Incredible to watch. Nice one.
     
  9. Emiel

    Emiel Well-Known Member S2G Supporter

    Messages:
    1,001
    Trophy Points:
    113
    Location:
    Western Europe
    I tried to fit the housing on an EX900. It won’t fit, the battery door could be made to fit perhaps. The rear casing differs too much.
     
  10. Yehuda Nataf

    Yehuda Nataf New Member

    Messages:
    13
    Trophy Points:
    3
    Location:
    Israel
    Imagine!
    Cool!
     
  11. T-ster

    T-ster Moderator Staff Member S2G Supporter

    Messages:
    1,464
    Trophy Points:
    113
    Location:
    England
    Can you share a link to the case please?
     
  12. Emiel

    Emiel Well-Known Member S2G Supporter

    Messages:
    1,001
    Trophy Points:
    113
    Location:
    Western Europe
    Beta Bux likes this.
  13. T-ster

    T-ster Moderator Staff Member S2G Supporter

    Messages:
    1,464
    Trophy Points:
    113
    Location:
    England
  14. Emiel

    Emiel Well-Known Member S2G Supporter

    Messages:
    1,001
    Trophy Points:
    113
    Location:
    Western Europe
    @T-ster: Help me find one for a DD, 700 series, or EX900 :)!
    I am willing to fund a first 10 or so when the price is reasonable.
     
    Last edited: Oct 9, 2023
  15. walkman archive

    walkman archive Administrator Staff Member

    Messages:
    1,887
    Trophy Points:
    113
    Location:
    Barcelona
    Very curious...
     
  16. Emiel

    Emiel Well-Known Member S2G Supporter

    Messages:
    1,001
    Trophy Points:
    113
    Location:
    Western Europe
  17. Radio Raheem

    Radio Raheem Well-Known Member

    Messages:
    1,961
    Trophy Points:
    113
    Location:
    uk
    have to say i'm not a fan it cheapens the whole walkman for me lads. yup i guess i am the odd one out as usual lol
     

Share This Page