I need some belts please.

I've sent you a PM.

So, how much for a "starter pack" of assorted belts?

Hello,

Looking for drive belts for the following Sony Walkman units:

WM-GX670 (Sony P/N 3-032-576-01)

WM-GX674 (Sony P/N 3-032-576-01)

WM-GX677 (Sony P/N 3-032-576-01)

WM-GX688 (Sony P/N 3-032-576-01)

WM-GX654 (Sony P/N 3-007-430-01)

I would imagine all these belts are 0.8 mm. As far as diameter goes, it seems to be around 2.2 " (55 mm). It's possible the belt for the WM-GX654 is slightly larger dia although I am presently using the 2.2" in that one too.

YES, THE BELT OF 674 IS A LITTLE MORE BECAUSE THE PULLEY HAS A GREATER DISTANCE DUE TO BE SMALLER PULLEY. ALL THESE BELTS ARE easy to find! THE BELTS ARE THE MOST DIFFICULT OF ULTRA THIN AND PANASONIC AIWAS. STRONG HUG

Not a hassle, have PMed you

DocP, I am looking for a drive belt for my wm f10?

Can you help,

Thanks

I received the belts today.

Thank you DocP.

WGrimes

Hey, DocP.

You wouldn't happen to have an assortment of 1mm sq belts with a circumference diameter of about between 70 & 90mm?

Cheers,

-pc

Hi DocP good to see your still here, must get some more belts off you soon, have quite a few walkmans in need of replacement belts. Joys of buying box lots. I bought two box lots of walkmans which i mentioned here some time ago and thankfully 95% of them just needed belts, talk to you soon

Phil

Hello,

I would seem that you are the man for belts!

I seem to be acquiring machines with drive belt and counter belt problems a lot these days from Sony WM ex808hg to Toshiba and Panasonic boomboxes and wondered if there is a 'selection box' of round, square and flat belts that i could get hold of and then replace them as they are used? Also some advice on measuring the belt required because some are stretched or broken. Thank you

Nick

dear friend - the advantage of stereo and bombooxes is that the straps can be thicker, square type industry, already require the walkmans thin straps and a low extent. it is necessary to measure puts them in a rule is not stretching it. I have helped her new friend

Sure thing Nick,

As most designs of tape transport mechanism in walkmans 'revolve around' similar belt size usage the assortment would be a safe bet for a collector or service person exosed to a wider range of pieces...have PMed you. Happy Collecting/Mending

this shortage of belts here in Brazil leave my walkmans stopped!! is unfortunate - because of a meager and simple little piece of rubber!!

hopefully something like this will help replace rubber belts (when/if I finally run out of my stock http://www.medicoil.com/prodexamstatic.php

Till then don't worry, you've got DocP

Can anyone help please? I have a Sony WM EX808EG that needs a belt and i have asked a couple of Americans through their ebay shops and they say that the required belt is very thin and the generic belts do not fit properly. They both said that there was no suitable replacement available. I have absolutely no reason to doubt DocP who has stated that his generic belts fit 95% of machines; but is the 808 one of the 95% or not? I will be buying a bundle of belts anyway but would rather know now, and keep looking! Thanks

Nick

 HIO wm-ex808 is an excellent Walkman - I have one that I use a lot!! you have good taste   - I'll look for you these belts - here in Brazil is practically impossible to find these belts, I have purchased many other countries - the problem is that these belts should be fine, and lock the pulleys and sheaves - I'll see if I can help you - strong hug

Thanks for that but to be honest; I have the Sony because it is supposed to be 'collectable' but in all honesty even the best Sony's sound nowhere near as good as a mid range Aiwa. Absolutely no contest! If only half of my Aiwa's had not had capacitor problems...............

I've just ordered a pack of belts to DOCP and I was very surprised when I received them. They came in the most beautiful letter I've seen in a long time.

Of course, an excellent pack of belts were also inside :-)

so, I think it's time to do my first belt replacing...

Thanks Dr!

Hey DOCP, I am in need of some belts for a Sony WM-10 and a Sony WM-100.  I know the WM-10 belt is 3 inches long because I happen to have an orignal one, my last one and I don't want to use it.  As far as the WM-100 goes I have no idea what the specs are.  if you can help that would be great!

AIWA HS-PX101  Uses a 135 mm stretched length belt almost similar to the wm10RV/40 belt. Although this size IS DIFFICULT to source I have 3 or 4 left.

Panasonic RQSX20 ( belts RDV0037 and RDV0038-2) 33mm and 24 mm belts ...not a problem at all. (members Gutman/Fotis/Costin Dan/Antun have reported that these sizes work fine)

Have replied to your PM, Not a problem at all

You are most welcome H, Thanks for the pics

here in Brazil is almost impossible to find these belts!! I get all the sony!! But if AIWA WITH THE PANASONIC AND ARE A TREMENDOUS HEADACHE!!!

As mentioned with the specs above, I have them if you want them ...as simple as that

dear amiggo: yes I'll have these belts because you're my last hope!! I have a box with 11 rare and expensive walkmans stopped for not having the straps right for them. hug him and then contact

Hi DOCP, i'm after some square belts for two sony dtc-1000es dat player, part numbers of the belts are below, hope you can help, i'm in the uk, would be happy to buy 4 sets of belts if you can help, or anything which is a close match?.

Control belt   

3-337-652-01

size 15mm dia 0.9mm thick

UD motor belt

4-918-923-01

20mm dia 1mm thick

Slide motor belt 

4-918-963-01

70mm dia 1.2mm thick

thanks

Andy

Hello DocP, i need a belt for my DCC170 recorder. I search a square belt of 65mm in diameter but 0.6 thickness. The original seems to be 0.5 but 1mm wont work. I will try 0.7 yours.

I think I will buy you the full set of : 25 belts(0.7/0.8mm).

PM me.

Hi DOCP, any news on the above?

Thanks

Andy

Sorry for the post Valentine's Day sluggishness

1. Jedi, have PMed you

2. Andy ...not a problem I've PMed you too

I'm blocked, I asked to DocP in PM the real thickness of his tiny belts. Because due to the design of the motor on the DCC130/134/170, it's impossible to put more than 0.7. The original size is 0.6.

See 4 last pictures at 

http://jonathan.dupre.free.fr/...dex.php?/category/95

Very frustrating. I will wait for his answer.

Dear Jedi,

I used a pair of 1/10th mm dental calipers to measure the thinner belts belts and I can safely say the cross sectional thickness is safely between 0.6 to 0.7mm. (have updated this info wherever possible in the thread)

Happy mending

DocP

hi there DocP, looking for the wm-fx55 drive belt, and u know where can i buy the headphone/remote jack? thanks

Hello DocP,

I've a wm-b602 in need of a belt and a wm-701c on the way that needs one, too.  I believe they both use the same part but I gladly concede to your experience.  Would you please be able to help me out with these?  

Welcome to the forum Gabe ,Kewik and n' Jeff. Check your PMs shortly ...belts shouldn't be a hassle at all

Happy Mending

P

Hi

 I have been pointed in this direction for a belt for my Aiwa hs-px 101?

I am looking for some belts too if possible.

thanks

Dan

Hey DocP,
I heard you're the man to go to for Belts! I pulled out a walkman at the back of my electronics draw and found a WM-7 but of course the belts gone! I've taken it apart and extracted the old belt but it's in pieces so I'm not sure what length it should be. Are you able to help me out with a belt? Please PM me if you are and how much it'd cost to send a couple to Aus (always good to have a spare)
Thanks 

Hi there,

I've just joined up here as I've just picked myself up a sony wm fx-453 and was hoping to track down a suitable belt for it. So good to see so many people still collecting and enjoying walkmans..I think I now have the fever!

I just got a Sony F-10II Walkman that would not play on tape. I took it apart and found the belt had pretty much turned to tar. I cleaned up everything and tried a belt I had handy from previous repairs of full size cassette decks. The belt proved to be to thick. Do you know where I can find the proper size belt for this unit?

Thanks.

hey DocP,

Do you have the belts for the sanyo 920? is starting to play a little sluggage.

can you please pm the price onthose.

Have sent you a PM